Search Our Site

Select a Category
Select a Manufacturer
Enter Keyword(s)

in 

Shop Our Site

TUFF TOE BOOT PROTECTOR

TUFF TOE Work Boot Toe Protection & Repair is a polyurethane adhesive with abrasion, chemical and water-resistant abilities that has been specially designed to provide long-term protection for your work boots, hiking boots, shoes and any other footwear that needs protecting.

Tuff Toe will extend the life of your boot by 3 Times! In tough work environments, boot toes are usually the first thing to wear out. With Tuff Toe, you will never tear out the front of your expensive work boots. Our ballistic grade polyurethane adhesive is the same material used by NASA. It is waterproof, and will resist punctures, chemicals and stains.
 
Tuff Toe respects American labor and is proudly manufactured here in the USA.
 
When expertly applied by one of our Tuff Toe Certified Professionals, we will guarantee our product for the life of your boot. Once it goes on, it’s not coming off!
 
How To Apply TUFF TOE Work Boot Toe Protection & Repair

STEP 1: TAPE – Use masking or painters tape to define the area of coverage. Tuff Toe will generally from the toe tip to 1-2 cm from where the steel toe ends. We don't recommend applying Tuff Toe to any flex areas. You can tape along the sole edge if you'd like a cleaner line, but this is not required.

STEP 2: PREP – Use the sand paper provided to scuff the coverage surface. Proper surface preparation is critical to adhesion. Make sure the entire surface has been sanded to ensure optimal conditions.

STEP 3: EQUALIZE CARTRIDGE & TIP – Tuff Toe is a two-part application that needs to mix simultaneously at the time of application. If the parts are not equal, the application will fail. To ensure equalization, push material out of both cartridges until they are both extracting equally into the mixing nozzle.

STEP 4: APPLY TUFF TOE – Hold the boot with your left hand (if you're right handed) and begin on the left side. Apply slowly from the sole to top. If you apply too quickly the material will come out runny and take-off on you. Applying slowly allows the material to begin setting so that it is thicker and easier to manage. If the material begins to run on you, simply turn the boot so that the material runs back into itself.

STEP 5: REMOVE TAPE – Immediately remove the tape. Pull carefully so that you don't mess up your application.

STEP 6: ROTATE – The material is still setting up and if you simply put the boot down the material will run to the sole. You want the material to be focused on the toe tip, so rotate the boot for 1-2 mins with the toe tip pointed down.

STEP 7: CURE FOR 24 HOURS – A full 24 hours is recommended for a full cure, however you will see that within 90 mins the material will be 80% cured. If you have to use your boots before the 24 hrs we recommend putting them in a warm area to help speed up the process (a hot car or in front of a heater works great).

IMPORTANT TIPS – Use Comet or a deglazing chemical to prep oily boots. If painters or masking tape won’t stick to your boots, not much will. Tuff Toe will dry with a glossy finish. If you prefer a matte finish, wait for 30-35 minutes until only slightly tacky (not sticky). Rub your finger across the Tuff Toe and the sheen will disappear and create a matte finish.

 TUFF TOE Work Boot Toe Protection & Repair is made to handle any punishment that you can give you work boots. No longer do you have to replace your work boots or buy ugly toe guards that don't do half of what TUFF TOE  Work Boot Toe Guard Protection & Repair does.

Keep those work boots and work shoes from wearing out with TUFF TOE protection. TUFF TOE  has been proven over the past 30 years to Triple the life of work boots. 

TUFF TOE Work Boot protects while repelling stains from, chemical colorants, grease, oil, dirt and water. 

Can be used on nearly any surface smooth leather goods, rubber and nearly any surface that is exposed to rough wear, from boots to saddles to tools.

 TUFF TOE Work Boot Toe Protection & Repair includes applicator kit and material to cover 1 pair (two boots). Includes applicator kit and enough product to cover two boots. Sets in just 30 minutes and cures within 24 hrs.

  • Category: Boot Protector
  • Brand: Tuff Toe

Options

SKU: Select A Color Price Quantity Status
TTB BLACK - -  In Stock
TTR BROWN - -  In Stock
TTT TAN - -  In Stock